The Pulsarlube EX electromechanical automatic grease lubricator is UL, ATEX certified
It is primarily designed to meet the following requirements: UL79, Power-Operated pumps for Petroleum dispensing products, 8th Edition ANSI/ISA-12.12.01-2000, Nonincendive electrical equipment for use in Class I , Division 2 , Group C and D Hazardous locations.
Pulsarlube EX consists of a vertical self-priming pump, microprocessor control system, and large LCD display. This product is ideal for applications where: considerable back pressure in lube line exists, a precise lubrication is required, or a disposable gas type lubricator is not economical.
The circuits and parts of the Pulsarlube EX are designed based on the energy limitation concept by adopting a non-sparking, explosion-proof structure that keeps an electrical device from sparking an explosive gas whether it is working under normal or certain abnormal condition.
Specifically designed for places where Class I, Division II, Group C & D certification is required
Substantial savings from the use of replaceable grease pouches and battery packs (Service Pack)
|Grease Pouch Capacity||125ml/250ml (replaceable)|
|Power Supply||DC 4.5V Battery Pack|
|Operating Pressure||Max. 15bar (218psi)|
|Operating Temperature||-15˚C~60˚C (5˚F~140˚F)|
|Dispensing Periods||1, 2, 3, 6, 12 month & H (15 days)|
|Remote Installation||Max. 3m (10ft) with O.D. Ø6 tube
(Direct mount is preferable)
|Certifications||ATEX, KCs, UL, CE|
|ATEX||Ⅱ 3 G / Ex nL ⅡB T5|
|UL||Cl.Ⅰ, Div. 2, Gps C, D|
|KCs||Ex nL ⅡB T5|
|CE / Etc.||CE (CoC)|
|Rating||Class l Division 2 Groups C.D||Ex nL IIB T5||Ex nL IIB T5|
|Maximum Surface Temperature||T6 (85˚C)||T5 (100˚C)||T5 (100˚C)|
|Enclosure Protection Indices||-||IP54||IP54|
|Classification Of Hazardous Locations||Cl l Div2||Zone2(gas)||-|
|Certificate Number||E304815||LCIE 07 ATEX 6100X||12-KB2BO-0279X|
The Pulsarlube EX is tested and certified by UL (USA), ATEX(Europe), and KTL(Korea), Refer to the above table when Certification for use in Hazardous Locations should be considered.
- Explosion Hazard – Do not remove or replace batteries unless power has been disconnected or the area is known to be free
of ignitable concentrations of flammable gases or vapors.
- This equipment is suitable for use in Class I, Division 2, Groups C and D Hazardous Locations OR non-hazardous locations only.
- SUBSTITUTION OF MOTOR AND REED SWITCH MAY IMPAIR SUITABILITY FOR DIVISION 2.
|Reference Designation||Description||Type of Protection|
|SW4||Reed Switch||Non-incendive Circuit|
|A001||Reducer, 3/8"F X 1/4"M Adaptor (Brass)
|A002||Reducer, 3/8"F X 1/8"M Adaptor (Brass)
|A002-S||Reducer, 3/8"F X 1/8"M Adaptor (Brass)
Socket + Pipe + Reducer
|A011||Socket, 1/4"F x 1/4"F Adaptor (Brass)
|A012||Socket, 1/8"F x 1/8"F Adaptor (Brass)
|A121||Pipe,1/4”M X 1/4”M × 50mm (Steel)
|A122||Pipe,1/4”M X 1/4”M × 100mm (Steel)
|A123||Pipe,1/4”M X 1/4”M × 150mm (Steel)
|A124||Pipe,1/4”M X 1/4”M × 200mm (Steel)
|A106||Pipe, 1/8"M x 1/8"M x 50mm for divider block (Steel)
|A107||Pipe, 1/8"M x 1/8"M x 150mm for divider Pipe, 1/8"M x 1/8"M x 100mm for divider block (Steel)
|A108||Pipe, 1/8"M x 1/8"M x 150mm for divider block (Steel)
|A109||Pipe, 1/8"M x 1/8"M x 200mm for divider block (Steel)
|A023||45° Elbow, 1/4”M X 1/4”F Adaptor (Brass)
|A024||45° Elbow, 1/8”M X 1/8”F Adaptor (Brass)
|A019||90° Elbow, 1/4”F X 1/4”F Adaptor (Brass)
|A020||90° Elbow, 1/8”F X 1/8”F Adaptor (Brass)
|A021||90° Elbow, 1/4”M X 1/4”F Adaptor (Brass)
|A022||90° Elbow, 1/8”M X1/8”F Adaptor (Brass)
If the bearing lube point is NPT, use the thread converter (A243) to convert thread metric to inch for bearing zerk (USA only)
1. All Parts should be assembled tightly with PTFE tape.
2. For optimal performance with remote installation kits, using an NLGI #1 grade grease is recommended.
3. If the bearing lube point is NPT, use the thread converter.
Kit No. 1250RC-1
|A002||Reducer, 3/8"F X 1/8"M Adaptor (Brass)|
|B002||Mounting Bracket, “L”Shape|
|B051||Self Drilling Screw, #8ⅹ20|
|A012||Socket, 1/8”F x 1/8”F Adaptor (Brass)|
|A240||Tube Fitting, Push-In Type, PC6-PT1/8”M
|A214-1||Distribution Tubing, O.D. 1/4"(6mm) Nylon Tubing, 10ft Pre-filled with (Grease Type)
|A243||Thread Converter, PT1/8"F X NPT1/8"M (Brass)
Note : For remote installation using a tube, use an 8mm O.D. (5/16″) tubing pre-filled with the same or compatible grease as the grease contained in the unit. Recommend using under short dispensing period settings due to powerful dispensing pressure.